Expert Answers about Heartland RV Cyclone Fifth Wheel
- Determining The Correct Replacement Landing Gears For A 2009 Heartland Bighorn 3670RL
- To determine the correct landing gears for your 2009 Heartland Bighorn 3670RL you'll want to measure the weld-stops of your current landing gears. Once we have these measurements we can determine the correct replacement so that you don't have to grind off and weld on new weld-stops.
For example, the Landing Gear Set w/ Handle # RVLG-8HDL has a 15-1/2" distance from bottom of upper weld stop to top of lower weld stop and 17-1/2" distance from top of upper weld stop to bottom of lower weld...
view full answer... - Recommended Storage Cover for 2008 Heartland Cyclone 3210 Fifth Wheel
- For your Heartland Cyclone 3210 that is 34 feet 10 inches, I recommend the Camco UltraGuard 5th Wheel Cover # CAM45756
This cover is designed to offer protection against all the elements, including snow, and even protects your trailer from heavy exposure to the sun and wind. The Adco also has zippered panels so you can gain access to your 2008 Heartland Cyclone 3210 if need be.
view full answer... - Correct Dexter E-Z Flex Suspension Kit for a Heartland Cyclone 4014
- The correct Dexter E-Z Flex Suspension Kit for your Heartland Cyclone 4014 is part # K71-656-00. The axle capacity note of 6,000 lbs has nothing to due with the actual weight capacity of the equalizer but rather the standard size equalizer used with a 6,000 lb axle that the above is designed to replace. The above Dexter E-Z Flex Suspension Kit will support the loaded weight of your Heartland Cyclone 4014 without issue so there should be no worries in this regard.
view full answer... - Correct Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box for Heartland Big Horn 3250TS
- The Gen-Y Hitch Shock Absorbing 5th Wheel to Gooseneck Pin Box part # GY58GR which is rated for 21,000 lbs will be more than enough for a 2008 Heartland Big Horn 3250TS.
view full answer... - How To Determine Fit of the Landing Gear Set RVLG-8000
- I don't have any specs on your 2008 Heartland Cyclone 4012 5th Wheel Trailer but all you need to do to confirm fit of the Landing Gear Set part # RVLG-8000 is measure the outer tube as well as the weld stop spacing on one of the legs. If the outer tube is 29-1/2" long and the distance between the weld stops is 15-1/2" inside to inside or 17-1/2" outside to outside then the above set will work for you.
view full answer... - Best Fifth Wheel Cover To Fit 42 Foot Cyclone Toy Hauler
- Since the Camco Ultraguard part # CAM45759 fits up to a 42 foot long fifth wheel, it will work for your trailer but has a possibility of being snug. It is a heavier cover that stands up to the elements compared to some of the other covers available that can be flimsy and rip or tear after being left outside.
view full answer... - Replacement Motor for Lippert Slide Out in RV
- If your Lippert slide out motor looks like part # LC141111 then the correct replacement motor is the part # LC167576.
view full answer... - Recommended Locking Lug Nuts for 5th Wheel Trailer
- It sounds like you are looking for a set of wheel locks for a trailer. If that is the case then the best option we have is the Wheel Lock Set for 1/2" Wheel Bolts part # RG01-150 which as the title states is for 1/2" studs. This is by far the most common stud size so most likely what you have but the only way to know for certain would be to remove a lug nut and measure the lug stud yourself. The other common size for a larger trailer is 9/16" but we don't offer a wheel lock for this size.
view full answer...
Go To Results